A standard pallet jack for a Euro pallet (800 x 1200 mm) has forks that are 1150 mm long and a total width of 540 mm, with two forks each 160 to 185 mm wide. That is the most commonly used combination. For other pallets, narrow aisles, or heavier loads, the ideal dimensions vary, and this article explores those in more detail.
Making the right choice starts with the pallet you move every day. By matching the dimensions of the pallet, forks, and load capacity, you can work more safely and prevent damage to the pallets. You can find more information about our pallet trucks on our product page.
What fork length is suitable for a Euro pallet?
For a Euro pallet measuring 800 x 1200 mm, a fork length of 1150 mm is standard. This allows the forks to span nearly the entire length of the pallet, ensuring that the weight is properly supported and the pallet remains stable during travel and lifting.
Why 1,150 mm and not 1,200 mm? The forks should not quite penetrate the pallet all the way through. If they extend too far, the front wheels will touch the floor beneath the pallet or the next pallet in a rack. If the forks are too short, part of the pallet will hang freely in the air. This increases the risk of the bottom shelves sagging and of the pallet tipping over when carrying heavy loads.
Also pay attention to the orientation. You can lift a Euro pallet from either side. If you lift the pallet from the long side (with the forks positioned across the 800-mm width), you’ll need a shorter fork of about 800 mm. This method is less common, but is used when loading narrow cargo spaces.
What are the fork width and overall width of a standard pallet jack?
A standard hand pallet truck has a total width of 540 mm, divided between two forks, each approximately 160 to 185 mm wide, with a gap between them. This dimension is designed to fit easily into the openings of a Euro pallet.
A Euro pallet has an opening of approximately 227 mm between the blocks on the short side. The forks must be able to fit through this opening without friction, but should not have too much play. For the standard size, the forks are spaced 540 mm apart from outer edge to outer edge, which fits standard pallet openings.
The total width also determines which aisles you can safely use. With a width of 540 mm, you can pass through most doorways and between standard racks. If the aisles are narrow, a narrower model may be the solution, as explained in the following section.
What is the difference between standard, long, and narrow forks?
Standard forks (1,150 mm long, 540 mm wide) are designed for Euro pallets. Long forks (up to 1,500 or 2,000 mm) lift longer or double pallets, and narrow forks (around 450 or 520 mm total) fit into tight spaces or pallets with smaller openings.
Standard forks: the all-arounder
The standard model covers the majority of daily pallet handling operations in warehouses, production facilities, and stores. They are widely available, easy to maintain, and fit on Euro pallets and many industrial pallets (1000 x 1200 mm) when loaded from the long side.
Long forks: for large or double loads
Long forks come in handy for 1200 x 1600 mm pallets, wooden crates, or when you want to move two pallets in a row at the same time. Keep in mind that the turning radius increases and the truck becomes harder to steer. This is something to consider for long distances or busy work areas.
Narrow forks: for limited space
A narrow pallet jack is useful in narrow aisles, for smaller pallet openings, or for pallets with an unusual design. The trade-off for that maneuverability is often a slightly lower load capacity or less stability when handling heavy, tall loads. So always check the combination of width and load capacity.
What dimensions do you need for non-standard pallets?
For non-standard pallets, the pallet opening determines the fork width, and the pallet length determines the fork length. As a rule of thumb, adjust the fork length to approximately 85 to 95 percent of the pallet depth, and choose a total width that allows the forks to slide into the openings without difficulty.
Common non-standard sizes include the industrial pallet (1000 x 1200 mm), the half pallet (600 x 800 mm), the quarter pallet, and the American pallet (approximately 1016 x 1219 mm). Each has its own opening and load capacity. For half pallets, a shorter fork—often around 800 mm—is sufficient, while larger sizes require longer forks.
Closed pallets, plastic pallets, or pallets with a trough and roll containers may also require a different approach. In that case, you should consider not only the dimensions but also the shape of the bottom and the height of the opening. Pallets with a low entry point require forks with a lower profile. You can find specific applications on our pallet handling page.
How do you measure the correct fork dimensions for your pallets?
Measure the pallet's external dimensions, the width of the openings between the blocks or planks, and the height of the opening from the ground. Also note the maximum weight of the load. With these four pieces of information, you can determine the correct fork length, fork width, fork height, and the required load capacity.
When taking measurements, follow these steps:
- Pallet length and width: Measure the outside dimensions in millimeters and also note the orientation in which the pallet will be loaded.
- Width of the openings: Measure the clear space between the blocks or support beams where the forks slide in.
- Opening height: Check to make sure the forks, including the front wheel or front roller, fit under the pallet.
- Load and weight: Determine the heaviest-load scenario, as the pallet truck’s load capacity must be well above that.
- Path: Measure the narrowest passage, aisle width, and turning space where you plan to use the cart.
Measure multiple pallets, not just the newest one. Wooden pallets wear out, warp, and sometimes vary in size. If you measure only one sample pallet, you run the risk that the truck won’t fit every pallet later on.
When is a custom pallet jack or consultation recommended?
A custom pallet jack or professional advice is recommended when standard sizes don’t fit, when you’re moving heavy or fragile loads, or when the daily workload becomes too much for your employees. A targeted analysis is also worthwhile in cases of intensive use or unusual working conditions.
Typical situations include:
- pallets with non-standard dimensions or unusual openings;
- very heavy loads where the load capacity of the pallet jack becomes critical;
- narrow aisles, elevators, or loading areas with limited turning space;
- repeated pushing and pulling over long distances, for which an electric model or pulling aid is more ergonomic;
- damp, cold, or dusty environments where a special version is required.
A workstation analysis reveals how your employees currently move pallets, where the pain points are, and what equipment really makes a difference. This helps you avoid investing in a model that looks good on paper but doesn’t work in practice. Also check out our pulling aids if the strain from pushing and pulling becomes too great.
How Logitrans Handling Helps You Choose the Right Fork Dimensions
At Logitrans Handling, we help you choose the right pallet jack based on your pallets, your space, and your employees. We consider not only the dimensions, but also ergonomics, safety, and efficiency, so that the solution works in practice and doesn’t create new problems.
Here's what you can expect from us:
- a free workstation analysis in which we assess your pallets, walking routes, and workload;
- advice on fork length, fork width, load capacity, and model, tailored to your application;
- a wide range of pallet trucks and related equipment, from manual to electric;
- the opportunity to test products in our demo room in Drongen, using your own pallets;
- Maintenance and follow-up through a maintenance contract, ensuring that your equipment continues to operate safely.
Not sure which fork dimensions are right for your situation? Feel free to contact us, and together we’ll find the solution that best fits your workplace.
Related Articles
- What is the difference between a lifting aid and a vacuum lift?
- What small changes can increase job satisfaction among operators?
- How can I demonstrate that my company takes the physical strain on employees seriously?
- What ergonomic aids are available for order picking?
- What types of machines can you use for lifting and stacking boxes?