To calculate the required pulling force of an electric tugger, multiply the total weight of the load to be pulled by the rolling resistance coefficient and, if there is an incline, add the incline force. Add a safety margin to the result. This will help you choose a tugger that can easily start and maintain movement of the load.
The result depends primarily on the weight, the surface, and the wheels of the load. Below, we’ll walk through the factors, the formula, the incline, and the starting force step by step.
What factors determine the required pulling force in practice?
The required pulling force is determined by the total weight of the load, the rolling resistance of the wheels on the surface, any incline, and the way the load is attached. The heavier the load and the rougher the floor, the greater the force the electric tow tractor must exert.
In practice, these factors play the biggest role:
- Total weight: Add up the weight of the cargo, the vehicle or trailer, and any equipment.
- Surface: A smooth, polished concrete floor offers little resistance, while joints, cracks, gravel, or tiles noticeably increase rolling resistance.
- Wheels and bearings: Hard polyurethane wheels on ball bearings roll more smoothly than rubber wheels or worn bearings.
- Uphills: Every incline requires extra effort in addition to rolling resistance.
- Frequency of use: Frequent starting and stopping puts a greater strain on the engine and battery than a steady drive in a straight line.
Collecting this information in advance helps prevent selecting a tractor that is either too heavy or too light. The type of load also plays a role: a pallet-handling train with multiple cars behaves differently than a single heavy roll container.
Which formula calculates the pulling force of an electric tractor?
The basic formula is: tractive force (N) = mass (kg) × 9.81 × rolling resistance coefficient. For a load of 1,000 kg and a coefficient of 0.02, this amounts to approximately 196 N. Additional force is required when dealing with inclines, friction in curves, or worn-out wheels.
The rolling resistance coefficient (often denoted by c or Cr) is the ratio of rolling resistance to weight. In practice, the following values are often used as guidelines:
- approximately 0.01 to 0.02 for hard wheels on a smooth, flat concrete floor
- approximately 0.03 to 0.05 for less favorable surfaces, worn tires, or small tire diameters
- higher values for rough, unpaved, or damaged surfaces
These are approximate values. The exact coefficient depends on the combination of wheel, bearing, and floor, so always check the specifications provided by the manufacturer of the cart or trolley.
Calculation example: You are pulling a 3,000 kg train across a smooth concrete floor with a coefficient of 0.02. The pulling force is then 3,000 × 9.81 × 0.02 ≈ 589 N. Add a safety margin to this calculation so that the tractor has sufficient reserve even under adverse conditions.
How do you calculate a slope or incline?
On an incline, you must add the gravitational force to the rolling resistance. That additional force is equal to mass × 9.81 × the sine of the angle of inclination—or, approximately, mass × 9.81 × the percentage grade divided by 100. Even a slight incline can more than double the required pulling force.
An example illustrates this. For a load of 1,000 kg on a 2% incline, the gravitational force is approximately 1,000 × 9.81 × 0.02 ≈ 196 N. The rolling resistance (with a coefficient of 0.02) is also 196 N, so the total force required is approximately 392 N. On a 5% slope, the gravitational force already increases to about 490 N.
On slopes and ramps, also be sure to:
- Braking capacity: When going downhill, the tractor must be able to safely slow down the load, not just pull it uphill.
- Traction: The tractor's drive wheels must have sufficient friction to pull the load without slipping.
- Maximum grade: Check the tractor's specifications, as not every model is suitable for every slope.
Why is the starting force greater than the driving force?
The starting force is greater than the driving force because, when pulling away, you must first overcome the static friction and the inertia of the load. Once in motion, only the lower rolling resistance remains. Therefore, a tractor with sufficient reserve power should be selected.
When the cart is at a standstill, the bearings, wheels, and deck are, as it were, locked in their starting positions. This temporarily requires a greater force, which in practice is often one and a half to two times the pushing force—or more when carrying heavy loads or using worn wheels. On top of that is the force needed to accelerate the load: the faster you want to accelerate, the greater the force required.
This effect is important in applications involving frequent stop-and-go operation, such as tugger trains in manufacturing or distribution. If you rely solely on the starting power, the tugger will be overloaded every time it starts up. This leads to wear and tear, engine overheating, and a shorter battery life.
How do you choose a tractor based on the calculation?
To select an electric winch, compare the calculated pulling force—including starting force and incline force—with the nominal and maximum pulling forces listed in the specifications. Choose a model with a sufficient safety margin, typically at least 20 to 30% above the calculated value.
Follow these steps one by one:
- Determine the maximum total weight of the load, even under the most extreme conditions.
- Calculate the driving force using the correct rolling resistance coefficient for your floor and wheels.
- Add the grade factor if your route includes a slope or incline.
- Take the starting torque into account and choose a model that can handle that peak.
- Add a safety margin and compare the result with the range of pulling aids available.
You should also check practical details such as the type of coupling, the battery capacity needed for a full workday, and maneuverability in narrow aisles. A calculation on paper is still just an estimate: a test run with your own loads on your own floor provides the most certainty.
How Logitrans Handling Helps Determine the Right Tractive Force
We help you accurately determine the required pulling force and select the right electric tugger, so you don’t end up investing in equipment that’s either too large or too small for your needs. As experts in ergonomic material handling, we guide you from analysis through to delivery, with a focus on safety and efficiency in the workplace.
Here's how we work:
- We start with a free workplace analysis, during which we assess weights, floors, slopes, and routes on-site.
- We calculate the driving force, climbing force, and starting force with an appropriate safety margin.
- You can test drive the tractor in our demo area in Drongen, using your own loads.
- Upon request, we provide training for users upon delivery.
- With a maintenance contract, we keep your equipment in optimal and safe condition.
Are you unsure about the right pulling force for your application? Feel free to contact us—we’d be happy to work with you to find the solution that truly fits your situation.
Related Articles
- How can you make emptying ingredient bags more ergonomic?
- What is the weight limit for lifting boxes per employee?
- As a warehouse manager, how much does absenteeism due to lifting injuries cost me?
- How can I reduce absenteeism due to physical strain in my warehouse?
- How do I request a demo for warehouse equipment?